Jim's blog - Sailing

Easter sailing

nospam@example.com (Jim) — Sat, 07 Apr 2012 23:32:54 +1200

Today, and yesterday for that matter, was one out of the box, so to speak. Despite the poor weather forecast a few days ago, the last couple of days have been absolutely superb.

Yesterday we walked over to a friends place in the morning, and had a few neighbours over in the afternoon - in both cases to indulge in hot cross buns while enjoying good company. Lot's of fun.

Today I went out and fitted the new tiller properly on Dovekie - and had a great test sail, together with Gordon who is always keen to go out. Heading out without the mizzen boom meant that we didn't have the full set of sails flying, but Dovekie slipped smoothly through the water with the light southerly winds that were blowing - probably between 8 and 12 knots.

Hands off..

We found that with a bit of careful trimming we could sail hands-off for short periods until a small gust headed us up a bit or a wave pushed us down.

We managed to hit over 6 knots several times, and sat on 4.5 knots running downwind from Titahi Bay into the ebbing tide - very satisfying.

Wing on wing..

Tiller lamination - step by step

nospam@example.com (Jim) — Thu, 26 Jan 2012 22:18:04 +1300

Last week I bought a couple of lengths of timber, kauri and mahogany, to laminate up for a new tiller.

The small scale plans that are in LHF's book "Sensible Cruising Designs" specify the tiller butt end dimensions at 2" x 2". The broken tiller is slightly larger than that.

I spent a couple of evenings this week slicing my timber into strips and planing them down to 6mm thick - the first significant use I have made of my De Walt planer that has been sitting under the bench for a year or so. I have also laid out the shape I will form the laminations to to get a nice (I hope) curve on the new tiller. The old tiller used to be slightly too close to the top of the cockpit aft coaming so I have curved it up a bit more than the old one. Hopefully the curve will not spring back too much when I release the clamps.

Mahogany and Kauri alternating strips ready to glue up

Saturday - I glued up the first 5 laminations today. First I costed the side that were going to be glued with un-thickened epoxy, and then I spread on a thick mix and clamped it up. I under-estimated the quantity I would need by quite a bit and ended up making 3 batches - very quickly I might add. I managed to get the ratio on the 2nd batch wrong and put in about 20% too little hardener. Hopefully it will still be strong enough to hold it all together.

Most of my clamps are cheap bar clamps, but today I bought a better quality Urwin one with a pistol type grip. It did a much better job of pulling in the tight part of the bends than the cheap bar clamps did when I did a test assembly. I'll get more over time I think although with epoxy I don't want to overtighten the clamps as the joint depends on the epoxy in between the wood.

New clamp is great

And thanks to my helper - good job Sam.

I tapered the tiller with a combination of a jigsaw and belt sander, rounded the edges with a router and have spent quite some time carefully filing and sanding to get a good shape and finish.

I drilled the hole for the retaining bolt oversized, filled it with a stiff epoxy mix and then drilled it out the right size. That should stop water getting into the inside of the bolt hole. The holes in the rudder cheeks are a little harder to deal with tough.

And the finish is paint on the butt end where it will be inside the tiller and 8 coats of varnish on the remainder. I am pleased with the outcome.

On the water

nospam@example.com (Jim) — Thu, 29 Dec 2011 22:29:57 +1300

I spent a bit of time yesterday fitting the new nav lights to the side of Dovekie's cabin, refitting the stove and then tidying and cleaning up a bit into a state that sailing could be contemplated. (Nearly) All my tools are at home now and I'll just take of the ones I need each time I go out.

This morning Jo and I headed down to meet Gord at the Dovekie's marina berth, a little later than intended but the weather was holding up. The clouds were obscuring the sun pretty well and the wind was fairly gentle. The idea was to head out around Mana Island, anchor in behind for a cup of tea and Xmas cake, and then head back home for lunch.

I got sails, halyards and things set up while Gord moved the anchor back into position up forward and connected the chain to the nylon warp, ready to drop once we got to a suitable spot off Mana.

Reversing out of Dovekie's berth is simple. She won't turn in reverse - at least not the direction she needs to, so its straight back, then forward with tiller hard over. With little wind the bow came around nicely and we didn't need to do a three point turn. The tide was coming up the channel so it was a slightly slower trip out to the bay than it can be but Mr Volvo played nicely and pushed us out. Gord pulled up the sails and we reached out almost due west at 5+ knots in 10-15 knots of (variable) wind.

Heading out of Karehana Bay

Once off the top end of Mana we headed downwind along the west side. There was a bit of a swell and short chop that Jo didn't really like but we got down far enough to start turning and noticed the white caps coming closer with the flood tide up Cook Strait heading against the wind.

Just before we got into the shelter of the island and headed for the anchorage and a cuppa, I found that I was holding the tiller in my hand and it wasn't connected to the rudder any more - in fact it was broken off and the stump end looked really rotten - BUGGA! The tide was pushing us toward the rocks at the south end of Mana and we couldn't steer. Gord jump up and dropped the sails, closely followed by the anchor. I jumped up and dived down into the cabin to grab a length of rope to lash the tiller back onto the side of the rudder, and made sure the VHF was on channel 16. Jo wondered what she was doing there at all and kept out of the way while I proceeded to slip coming out of the cabin with my piece of rope as a wave went under us, and head butted the mizzen mast while I scraped the skin of my shin on the top of the companionway.

It didn't take long to get the tiller lashed to the rudder head, decide it would cope with the load, start the motor, lift the anchor and get under way again. The lashing slipped and needed to be tightened several times as we motored back to the berth. It wouldn't have been quite as much of a problem if the offset propeller didn't keep turning us off course to port all the time so needing constant pressure to go straight even when the waves/swell (now coming abeam us) weren't trying to do the same.

Luckily the tide was almost full in the channel so there was only a little current to worry about and the jury-rigged rudder coped with that just fine. Likewise getting into the berth was a cinch with no wind to blow the bow off.

Not a great trip for Jo's first on Dovekie but a good run for the new motor.

I'm glad the tiller didn't break when we were close in a lee shore as we came around the south end of Mana - the water gets deep quite quickly so my 100 feet or so of anchor warp would have been struggling to hold us.

Approaching the south end of Mana Island

I'll be able to refit the tiller if I shorten it a bit but it is getting a bit rough so I'll get started on making a new one. I'm thinking light and dark woods laminated into a neat curve and varnished - or maybe not.........

Seals

nospam@example.com (Jim) — Wed, 07 Dec 2011 13:13:24 +1300

Over the last couple of months there have been several young seals living in the Marina. Sleeping on the end of a pier, and swimming around chasing fish at other times.

Couple of weeks ago there was a dolphin under the road bridge nearby too.

Time flies

nospam@example.com (Jim) — Mon, 05 Dec 2011 13:27:19 +1300

Dovekie is coming along well now.

I have finished painting the cabin top/side/cockpit and still need to run around the deck to seal of the tiny cracks along the planking. I am very pleased with the colour of the non-slip areas of the cabin top - Altex Kumeu White. There is no water leaking in so I am hopeful the putty between planks is sound (apart from a few places I have replaced).

I have undercoated the inside of the cockpit bulkhead where i replaced a big patch of ply and need to get some top coat on - another short job but just one on the list.

I refitted the winches on Saturday after cleaning and re-greasing. They spin well now. Still need new jib-sheets and to set up the reefing arrangement.

The floors from the stern and port side lockers are at home for painting. They don't need much so I'll do them one evening, or two counting undercoat.

The angled blocks for mounting the nav lights on the side of the cabin top are roughed out but need a bit more shaping before fitting. Looking at some on other boats I seem to be over-thinking it but there is no point in having them if they are not set up correctly. Maybe it's not so important when you are bobbing around all over the place and a few degrees of alignment are academic.

Mel bought me a GrabOne voucher for a discount in the Barton Marine shop so I went in with her and Sam yesterday to buy him a junior sized life-jacket in preparation for his first time out sailing. Will need to make that a calm day so he isn't put off. Maybe after Xmas.

Progress

nospam@example.com (Jim) — Wed, 12 Oct 2011 16:58:50 +1300

I spent a good deal of last weekend doing things other than working on Dovekie. However I did get some work time down there on Monday after a brief visit on Sunday with Sam. There a a couple of baby seals living in and around the marina and they were sleeping on the end of C pier. Spon after Sam and I got to the boat I noticed that one of them was playing around not far from us so Sam had a great view of the baby seal. He now associates that with 'grandad's boat'.

When I finally got down there on Monday afternoon there was one of the seals chasing small fish all around the pier I am on. I first noticed him about 5 meters away gulping down a fish, later with another fish and a little later again I saw him chasing a fish just below the surface and not quite catching it. The fish were maybe 180mm long so not exactly a big meal.

Once the seal was out of the way I managed to sand and get a first top coat over the cockpit floor, seat fronts and tops, and sanded and undercoated all the cockpit hatch covers. Also got a coat of undercoat on one side of the cabin top.

I picked up some plated brass fairleads and a cleat at a good price on Trademe last week so have to figure exactly where they will go.

200mm cleat and fairleads.

I have removed the old side nav-lights as the plywood supports were rotting a bit. I found that there wasn't as much bedding under them as there should have been and one of the screws pulled straight through the cabin top so I need to fix that too.

Lots of little jobs but hopefully sailing as soon as the next two top coats in the cockpit are dry (and they are water based so one good day will suffice for that).

And there is still no water coming in after some pretty heavy rain so pleased with that.

Slow progress

nospam@example.com (Jim) — Mon, 19 Sep 2011 21:11:18 +1200

I have finally got some paint on the new cockpit work. The new grand-daughter has been a big distraction over the last month, and I have spent quite a bit of time looking after grandson Sam at weekends. He now understands 'grand-dad's sailing boat' and is keen to visit. Maybe this coming summer he'll come out with me on a good day or two.

Saturday afternoon I did a bit more sanding and then primed the repairs in the cockpit of Dovekie. I had hoped to get a second coat on today but the rain prevented that.

Hopefully next weekend I'll get the cockpit painting finished. I did find another tiny area of rot at the edge of one of the seat top lockers but that should be easy to repair. No doubt there are others I haven't located yet.

Friend Gordon has run a sander over much of the cabin roof and some of the fore-deck so that is the next target. I'll do a quick pass over them with a finer sander, hand sand edges and corners and get some primer and undercoat on those pretty soon now. Here is a pic Gord took recently.

I found the problem with the house battery was that the new voltage sensing relay that was fitted with the motor didn't have its earth wire connected. A quick fix and I hope the long time spent mostly discharged hasn't hurt the battery too much.

I still need to sort the nav lights and the main sail reefing out but that shouldn't be too complex. I have made up new handrails for the cabin roof out of kwila. They have come up really nicely and are much more solid than most that are around at 65x35mm rather than 50x25. I'll bolt them through the cabin roof beams so they will be a lot more useful than the old ones that were just screwed in and getting loose.

I'll also remove the old job halyard that has been getting in the way a bit. The original fractional rig was replaced with a mast head roller furler so the old halyard is redundant. Sometime I'll need to figure out how to rig my spinnaker. If it was flown from the same point as the head of the jib it will be too small and there is no fitting for it at the mast head.

It's paying off ...

nospam@example.com (Jim) — Thu, 14 Jul 2011 16:53:09 +1200

I went out to Dovekie last night to check the mooring lines and bilge water after the few days of stormy wind and rain we have had, and was pleasantly surprised.

There was almost no water in the forward area of the bilge and only a litre in the aft section. That is excellent given the weather we have had. There are still a couple of leaks around the hatches that I haven't got to yet but they will be taken care of by the glassing and painting I will do. The rot areas in the cockpit are basically watertight now.

The mooring lines were OK but I have to put plastic tube around one of the aft ones that is rubbing on the toe-rail. It was going through a fairlead but the angle of it with the wind we have been having (more westerly than usual) has resulted in some chafing. It now runs straight out over the toe-rail but still rubs a little.

Unfortunately I found that my house battery was a bit run down due to my leaving the main switch turned on at the weekend and the depth sounder running it down. There must be something else as I would have thought that the depth sounder by itself wouldn't run it own that fast. Anyway the new motor has a 114A charging capability so a brief run should top it up well. Hopefully that will be on Saturday when the forecast is very good for some time under sail. The 50+ knot winds of the last few days were not encouraging at all.

We learn as we go..

nospam@example.com (Jim) — Wed, 13 Jul 2011 08:41:08 +1200

So I finally got around to cutting out the rot on the forward port corner of the cockpit. Like the corner on the other side the rot extended into the ply of the bulkhead. I removed the Formica lining on the inside and found several interesting things. There was a cut-out in the bulkhead for an instrument of some kind that had never been repaired. Just covered over with the teak panelling on the outside and by the formica on the inside. I could see straight out through the gaps between the panelling so water has been running down against the ply for a long time.

There was another hole about 3 inches in diameter that had been patched - probably a small compass from way back.

I also cut a small square out around where the corner of the seat top outside aligned with. I found that there was some rot inside the ply, but it wasn't too bad. I have soaked it in preservative and penetrating epoxy so hopefully that will, together with stopping the water getting in, keep it from getting any worse until some time in the future when someone will pull it all apart and rebuild it properly.

I have bought two pieces of kwila to make new handrails from. Its a quarter the price of teak and I'll see how it goes. I am making them really beefy compared with the old ones, and will bolt them through the cabin roof beams instead of just screwing them in. Cutting out the first two was easy with a good hole saw. I bought a new Bosch 60mm hole-saw and it cut through the 31mm thick kwila very cleanly, if somewhat slowly to stop my light-weight drill-press from stalling. Ran the router around the edges and they are very cool looking. I still need to figure out the right angle to suit the cabin roof and plane the bottom to suit, round off the ends, drill mounting holes and give a good all-over sand to smooth out the few rough parts.

I have also turned down the heads of some screws a size up and a little longer than the originals to refix the sail track to the mast. That seems to have worked well.

Looking at LED nav lights now, a bosun's chair to get up the mast to fix in place, and thinking about what else I need before venturing across Cook Strait.

Dovekie today

nospam@example.com (Jim) — Thu, 07 Jul 2011 17:00:43 +1200

Dovekie is not quite the original H28 design but pretty close apart from the raised coach roof and a few areas the have been glassed.

The issues I have with it are not with the riveted kauri hull and frames which (apart from a couple of broken frames) appear to be in good nick and pretty much water tight. What are problems is where the cockpit floor and seat were built from ply and some epoxy and glass, and where the compass was fitted through the plywood cockpit bulkhead.

I have rot in three of the four corners where a steel nail was driven down through the seat frames into plywood (2x2 nailed into 1/2 in ply - who would do that???) Water has got in around the nails, run down into the ply and spread sideways. In each case the rot is in only one horizontal ply. The vertical ones appear to be wet near the nail but solid still. The wood appears to be different in each ply but the glue seems to have prevented the rot going across between plies in most areas apart from close to the nail. One nail went through into an original deck beam which is the only structural part that I have found with rot.

The cockpit floor has been glassed but it hasn't been taken up the sides at all - just a filler coving which has now cracked away from the vertical sides and getting a little wet. I am in the process of fixing the rot and am cutting out the filler (thanks to my Bosch multitool) and will redo with a glass layer a few inches up each side.

The compass was fitted to the cockpit bulkhead and not sealed properly. The ply was quite wet and had been repaired before but the rot I found was due to the cockpit seat problem above.

Interestingly the side decks are planked and caulked and also appear sound in the areas I have stripped of paint so far. There is a lot to be said for the old methods.

Jeezzz - a bit of a rant - I needed to get that off my chest - its been frustrating dealing with a number of individual small problems that all could have been avoided, are all individually not difficult to repair but which add up to quite a bit of work.

A Good Friday

nospam@example.com (Jim) — Tue, 26 Apr 2011 14:22:39 +1200

Good Friday seemed better weather-wise than predicted so when Gordon turned up to see how progress with the rot repairs was progressing, I finished the template for the plywood patch I was cutting out and we headed out for a sail. The wind was fresh but not too strong and we tried sailing on just the heads'l + mizzen. Dovekie loved that combination - very well balanced and nicely powered - not too much, not too little.

I had also fitted the first patch piece of kauri below the companion sill board so that is now done. Still one more piece to make and fit there. I went back on Saturday and started soaking the cutout area with thinned Everdure to try and seal in any rot spores that I haven't managed to remove in the ply edges. Sunday added another coat. It's close to ready to patch up now once I do the cockpit seat front corner. That will need a good couple of dry days to ensure there is no damp left around, and more Everdure in the edges once I cut it out.

I caught up with Gavin Pascoe - my one-time crew mate on Lady Mink when we helped Dave Parsons back from Vanuatu. Gavin has several projects under way including "Lizzie" that he was busy fitting a new beam to on Saturday with lashings of red-lead+putty bedding under the joins and around the bronze screws. "Lizzie" should be magnificent once he finishes rebuilding her with new mahogany brightwork. Gavin also owns "Shemara", another 50 something year old kauri yacht like Dovekie.

A great day

nospam@example.com () — Wed, 16 Feb 2011 10:23:01 +1300

Anchored off south east side of Mana Island

Last Saturday Gordon and I headed out in Dovekie for his first trip. We motored out into Karehana bay with about 10 knots of wind and had a good sail out around Mana Island. The wind was between 10-15 knots most of the time.

Dovekie was nicely balanced with almost no weather helm once we got the the mizzen adjusted more or less right. I still have some learning to do there.

We anchored in behind Mana Island for lunch with another H28 and a couple of other yachts. There were a lot of small boats out fishing too.

Very pleased on the whole with how the day went.

Just anchored - Mana Island

I have added a fire extinguisher and another life jacket into the on-board equipment, and installed a new shackle for the anchor rode/chain link as there wasn't one at all. Actually looking at the advertisement that Vinings had for Dovekie it looks as though the last owner removed a bunch of things as the price dropped on Trademe. There is no barometer, clock, 2nd anchor or storm sail on board.

Dovekie leaves her berth

nospam@example.com () — Mon, 31 Jan 2011 19:50:53 +1300

First short trip - Mana Island astern

After at least a year and probably more, Dovekie has again sailed under her own power.

Sunday morning my friend Rob met me and we motored Dovekie out into Karehana Bay. With the forecast predicting gale force winds in the afternoon we weren't planning to stay out long but we did give the motor a workout and sailed on just the jib for a bit.

I have set up the bilge pumps with a float to come on automatically, to please the insurance company and cleaned up he remaining water in the bilge so I can measure what is actually coming in. We also redid the out-haul and other lines on the mizzen as they were a bit of a mess. I need to figure out the reefing for the main sail too. There are no fittings to ease taking in reefs so I'll need to either set up lashings or install some fittings.

Dovekie floats again

nospam@example.com () — Sat, 15 Jan 2011 20:26:11 +1300

Painting completed

I've been home over a week now and have progressed the painting on Dovekie. Three coats of good house paint above the water line - slightly off white, and finally the anti-foul was finished last Monday after putting it off due to the dust raised by the wind on Sunday. I also wired up two bilge pumps with fuses and on/off switches ready for the anticipated seams leaking.

I booked the travel lift for 4pm Friday afternoon and the photos show the progress courtesy of my friend Rob who came down to lend a hand.

Ready to lift

And just finishing off the hard to get to areas on the bottom of the keel.

Touching up those hard to get to places

A little nervousness on first powering up the new Volvo Penta 20hp motor but it all started and ran beautifully.

Ready to roll...

I was surprised at the surge of power when I headed off for my berth. I was even more surprised to get half way down the pier to find and find Peter from the marina office pointing me into a berth halfway down instead of the one I have been paying for. It turns out that the owner of the berth died last week and his family want to get rid of the berth, and his boat which is now parked in it. Peter is locating me an alternative one.

Anyway once we were safely parked up in the new (temporary) berth we sorted out the mooring lines which weren't optimised for Dovekie's size while keeping an eye out for water coming in the seams. There was a little immediately apparent but I spent the night on board waking up several times to check the water level. I pumped out maybe 8 litres, fitted the first of the cleats to the mizzen mast and went home to baby-sit young Sam. Today I went back out and pumped another 10 litres which isn't bad for nearly 24 hours - the seams are pretty tight despite the drying out.

Temporary home

Not going to make it

nospam@example.com () — Tue, 21 Dec 2010 10:21:15 +1300

The weather over the last few days plus being out of town Saturday means that unfortunately I am not going to get Dovekie back in the water before I go away for 2-3 weeks over Xmas/New Year. I

The new motor is in and has been run. Gavin uncovered a couple of minor issues that he sorted along the way. The thru-hull for the sea water intake for the motor had been seriously eroded by electrolysis so that has been replaced, and he found a small area of rot in the plywood backing of the old throttle control in the cockpit so has replaced that too.

I have the parts ready to wire up the new bilge pump which is a prerequisite to going back into the water but that will have to wait now. I need to finish repairing the little rotten hole in the cockpit bulkhead too but that too will wait - and won't stop the boat floating so isn't on the critical path. I need to get out there tonight to make sure that there is no way the weather can get in while we are away.